View 20-PB06IPB010RC-P955A40Y_9029124.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet flow ipm 1b 600 v / 10 a ciptopology (converter + inverter + pfc) optimized for pfc frequencies of 20khz..100khz and inverter frequencies of 4khz..20khz integrated pfc controller circuit with programmab le dc output voltage and pwm frequency inverter gate drive inclusive bootstrap for high side power supply solder pins over current and short circuit protection integrated dccapacitor sense output of dccurrent temperature sensor one side, no input output xing pressfit optional preapplied thermal interface material fans and pumps aircon electrical tools low power industrial drive 201b06ipb010rcp955a40 20pb06ipb010rcp955a40y t j =25c, unless otherwise specified parameter symbol value unit repetitive peak reverse voltage v rrm 1600 v t h =80c 16 t c =80c 21 t h =80c 19 t c =80c 29 maximum junction temperature t jmax 150 c pfc igbt collectoremitter break down voltage v ce 650 v t h =80c 19 t c =80c 20 t h =80c 37 t c =80c 56 gateemitter peak voltage v ge 20 v maximum junction temperature t jmax 175 c t j =tjmax t j =tjmax p tot i 2 t t p =10ms 50hz half sine wave 130 a features flow ipm 1b target applications schematic dc forward currentsurge forward current t j =150c 80 types i2tvalue maximum ratings i fav a2s i fsm condition input rectifier diode a repetitive peak collector current t j =tjmax turn off safe operating area a a power dissipation dc collector current i c w power dissipation t j =tjmax v ce 650v, t j t op max t p limited by t jmax i crm w p tot a 9090 conclusive power flow, all power connections on copyright vincotech 1 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet t j =25c, unless otherwise specified parameter symbol value unit maximum ratings condition pfc inverse diode t h =80c 6 t c =80c 8 t h =80c 12 t c =80c 19 pfc diode t h =80c 13 t c =80c 16 t h =80c 25 t c =80c 37 inverter transistor t h =80c 9 t c =80c 12 t h =80c 20 t c =80c 31 t sc t j 150c 5 s v cc v ge =15v 400 v inverter diode t h =80c 8 t c =80c 11 t h =80c 17 t c =80c 25 surge forward current i fsm t p =8,3ms 180 a i 2 t value i 2 t 60 hz half sine wave 130 a t j =tjmax a c v 600 c 175 v rrm p tot v ce i c v ge i crm t j =tjmax p tot i f v rrm i frm 20 w av a 600 a v t j =tjmax v ce 600v, t j 150c t j =tjmax t p limited by t jmax w 175 i f p tot t jmax turn off safe operating areapower dissipation maximum junction temperature power dissipation 650 c power dissipation w peak repetitive reverse voltage 175 dc forward currentrepetitive peak forward current t jmax maximum junction temperature 60 t p limited by t jmax t j =tjmax v repetitive peak forward current a 175 aa t p limited by t jmax t j =tjmax maximum junction temperature dc forward current i f peak repetitive reverse voltage t j =tjmax c w a v t jmax t jmax i frm gateemitter peak voltagepeak repetitive reverse voltage power dissipation maximum junction temperature short circuit ratings repetitive peak collector current collectoremitter break down voltagedc collector current dc forward current p tot 12 650 v rrm 30 20 t j =tjmax copyright vincotech 2 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet t j =25c, unless otherwise specified parameter symbol value unit maximum ratings condition pfc shuntpfc controller* v cc 26 v t jmax 125 c * for more information see infineon's datasheet ice3pcs02 dc - shuntdc link capacitor gate driver* * for more information see infineon's datasheet 6ed003l02f2 thermal propertiesinsulation properties v is t=2s dc voltage 4000 v min 12,7 mm min 12,7 mm cti >200 insulation voltagecreepage distance clearance comparative tracking index operation temperature under switching condition t op 40+(tjmax 25) c storage temperature t stg 40+125 c output voltage (fault) u out vcc+0,5 v 20 v input voltage (lin, hin, en) u in 10 v maximum dc voltagesupply voltage u cc w v 500 v max t c =25c power dissipation p tot 3,2 i f 8 a maximum junction temperaturedc forward current v freq pin voltage v f req 5,3 v vsense current i vsense 1 ma vsense voltage v vsense 5,3 w power dissipation p tot t c =25c 9 dc forward current i f t c =25c 10 a vcc supply voltage vcc common with gate driver ic copyright vincotech 3 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet parameter symbol unit v ge [v] or v gs [v] v r [v] or v ce [v] or v ds [v] i c [a] or i f [a] or i d [a] t j min typ max tj=25c 1,04 tj=125c 0,97 tj=25c 0,87 tj=125c 0,74 tj=25c 25 tj=125c 33 tj=25c 0,01 tj=125c thermal resistance chip to heatsink r th(j-s) 3,66 tj=25c 3,3 4 4,7 tj=125c tj=25c 2,12 2,22 tj=125c 2,44 tj=25c 0,04 tj=125c tj=25c 27 tj=125c 28 tj=25c 5 tj=125c 7 tj=25c 122 tj=125c 154 tj=25c 2 tj=125c 2 tj=25c 0,1516 tj=125c 0,2417 tj=25c 0,0317 tj=125c 0,0583 thermal resistance chip to heatsink r th(j-s) phasechange material = 3,4w/mk 2,56 k/w tj=25c 1,23 1,12 1,87 tj=125c 0,97 thermal resistance chip to heatsink r th(j-s) phasechange material = 3,4w/mk 7,75 k/w tj=25c 1,92 2,22 tj=125c 1,97 tj=25c 1,6 tj=125c tj=25c 15 tj=125c 19 tj=25c 22 tj=125c 36 tj=25c 0,2008 tj=125c 0,4358 tj=25c 0,0150 tj=125c 0,0504 tj=25c 2033 tj=125c 891 thermal resistance chip to heatsink r th(j-s) phasechange material = 3,4w/mk 3,87 k/w 400 10 e rec r 650400 400 u cc =15v 25 10 v ce =v ge turnoff delay time e on t d(off) turnon energy loss per pulse fall time t d(on) i ces v f c ies v ge(th) v f gate emitter threshold voltagecollectoremitter saturation voltage pfc igbt v cesat t r t f e off q rr i rrm i rm c rss c oss t rr reverse leakage currentreverse recovery time reverse recovered energy peak rate of fall of recovery current reverse recovery charge pfc shunt r1 value pfc inverse diodepfc diode forward voltage diode forward voltage output capacitancereverse transfer capacitance collectoremitter cutoff rise time input capacitance turnoff energy loss per pulse turnon delay time value conditions characteristic values forward voltagethreshold voltage (for power loss calc. only) slope resistance (for power loss calc. only) v f v to r t input rectifier diode 7 77 k/w vv m ma reverse current i r 0,000330 v 1510 10 peak recovery current 1200 phasechange material = 3,4w/mk 50 45 7,7 2100 a ns ma mws vv v mws ns a pf m c 00 f=1mhz a/s u cc =15v 15 tj=25c ( d i rf /d t ) max copyright vincotech 4 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet parameter symbol unit v ge [v] or v gs [v] v r [v] or v ce [v] or v ds [v] i c [a] or i f [a] or i d [a] t j min typ max value conditions characteristic values tj=25c 4,4 5 5,6 tj=125c tj=25c 1,88 2,20 2,62 tj=125c 2,32 tj=25c 0,002 tj=125c tj=25c 120 tj=125c tj=25c 582 tj=125c 631 tj=25c 20 tj=125c 25 tj=25c 837 tj=125c 950 tj=25c 16 tj=125c 22 tj=25c 0,1950 tj=125c 0,3241 tj=25c 0,1611 tj=125c 0,2042 thermal resistance chip to heatsink r th(j-s) phasechange material = 3,4w/mk 4,72 k/w * chip data ** including gate driver tj=25c 1,68 2,23 2,42 tj=125c 2,18 tj=25c 6 tj=125c 6 tj=25c 179 tj=125c 276 tj=25c 0,3566 tj=125c 0,6738 tj=25c 181 tj=125c 46 tj=25c 0,0867 tj=125c 0,1610 thermal resistance chip to heatsink r th(j-s) phasechange material = 3,4w/mk 5,72 k/w dc link capacitor none tj=25c 64 655 nf m tj=25c 10 15 0 u cc =15v u in =5v v ge(th) v cesat v ce =v ge t r i ces r gint i ges r c r2 valuec value dc - shunt c rss q rr t rr i rrm v f q g t d(on) t d(off) output capacitance turnoff energy loss per pulse rise time t f e on e off c oss integrated gate resistorturnon energy loss per pulse inverter transistor gate emitter threshold voltagecollectoremitter cutoff current incl. diode fall time turnoff delay time ** turnon delay time **input capacitance collectoremitter saturation voltage* 0 20 15 f=1mhz u cc =15v u in =5v 0,0001710 6 e rec gate chargereverse recovered energy peak rate of fall of recovery current c ies reverse recovery timereverse recovered charge inverter diode peak reverse recovery current reverse transfer capacitancediode forward voltage gateemitter leakage current 25 0480 400 10 600 6 400 tol. 1% 22 v ns c a pf a/s mws nc na ma v mws ns 37 v tj=25c 25 100 ( d i rf /d t ) max copyright vincotech 5 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet parameter symbol unit v ge [v] or v gs [v] v r [v] or v ce [v] or v ds [v] i c [a] or i f [a] or i d [a] t j min typ max value conditions characteristic values gate driver supply voltage u cc tj=25c tj=125c 13 15 17,5 v quiescent vcc supply current i qcc tj=25c tj=125c 1,3 2 ma input voltage (lin, hin, en) u in tj=25c tj=125c 0 5 logic "0" input voltage (lin, hin) u i h tj=25c tj=125c 1,7 2,1 2,4 logic "1" input voltage (lin, hin) u il tj=25c tj=125c 0,7 0,9 1,1 positive going threshold voltage (en) u en, th+ tj=25c tj=125c 1,9 2,1 2,3 negative going threshold voltage (en) u en, th- tj=25c tj=125c 1,1 1,3 1,5 input clamp voltage (lin, hin, en) u in, clamp i in = 4ma tj=25c tj=125c 9 10,3 12 itrip positive going threshold u tr, th+ tj=25c tj=125c 380 445 510 mv input bias current lin high i lin+ u lin = 3,3v tj=25c tj=125c 70 100 input bias current lin low i lin- u lin = 0v tj=25c tj=125c 110 200 input bias current hin high i hin+ u hin = 3,3v tj=25c tj=125c 70 100 input bias current hin low i hin- u hin = 0v tj=25c tj=125c 110 120 input bias current en high i en+- u hin = 3,3v tj=25c tj=125c 45 120 output voltage (fault) u flt tj=25c tj=125c 0 u cc v low on resistor of pull down trans. (fault) r on, flt u fault =0,5v tj=25c tj=125c 45 100 pulse width for on or off t in tj=25c tj=125c 1 s turnon propagation delay (lin, hin) t on tj=25c tj=125c 400 530 800 turnoff propagation delay (lin, hin) t off tj=25c tj=125c 360 490 760 fault reset time t rst tj=25c tj=125c 4 ms fixed deadtime between high and low side t dt tj=25c tj=125c 150 310 ns vcc turnon threshold v ccon 11,5 12,0 12,9 v vcc turnoff threshold v ccuvlo 10,5 11,0 11,9 v operating current with active gate i cchg c l =1nf 6,4 8,5 ma operating current during standby i ccstby 3,5 4,7 ma pfc switching fequency f swnom 20 khz dc link voltage dc2+ 339 350 361 v dc link treshold (ovp1) low to high v ovp1l2h 108 % dc link treshold (ovp1) high to low v ovp1h2l 100 % blanking time for ovp1 t ovp1 12 s dc link treshold (ovp1) hysteresis v ovp1_hys 6 8 11 % dc link treshold (ovp2) low to high v ovp2_l2h 428 443 460 v dc link treshold (ovp2) high to low v ovp2_h2l relative to ovp2 92 % blanking time for ovp2 t ovp2 12 s tj=25c vincotech ntc reference bvalue tol. 3% b b ( 25/100) tj=25c bvalue b (25/50) tol. 3% k tj=25c 3950 k 3998 22000 % 12 12 **dc link voltage is setable by an external resistor between pins 32 (see figure 2 for values) tj=25c v a u cc = 15v relative to output voltageovp1 values varies with external resistor set with an internal resistor r freq =220k* set with an internal resistor divider** 2 200 mw/k power dissipation p mw rated resistance r power dissipation constant deviation of r100 r/r r100=1486 thermistor tj=25c tj=25c tj=100c tj=25c u lin = 0v; u hin =3,3v *switching frequency is setable by an external resistor between pins 32 (see figure 1 for values) u lin/hin = 0v & 3,3v u lin/hin = 0v or 3,3v feedback voltage v dclink /130 can be measured at vsense pin pfc controller ns u lin/hin = 0v or 3,3v copyright vincotech 6 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 1 output inverter igbt figure 2 output inverter igbt typical output characteristics i c = f( v ce ) i c = f( v ce ) at at t p = 250 s t p = 250 s t j = 25 c t j = 125 c u cc from 10 v to 17 v in steps of 1 v u cc from 10 v to 17 v in steps of 1 v figure 3 output inverter fwd typical diode forward current asa function of forward voltage i f = f( v f ) at t p = 250 s output inverter typical output characteristics 0 5 10 15 20 25 30 35 0 1 2 3 4 5 v ce (v) i c (a) 0 5 10 15 20 25 30 35 40 0 1 2 3 4 5 v f (v) i f (a) t j = 25c t j = t jmax -25c 0 5 10 15 20 25 30 35 0 1 2 3 4 5 v ce (v) i c (a) copyright vincotech 7 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 4 output inverter igbt typical switching energy lossesas a function of collector current e = f( i c ) with an inductive load at t j = 25/125 c v ce = 400 v u cc = 15 v figure 5 output inverter fwd typical reverse recovery energy lossas a function of collector current e rec = f( i c ) with an inductive load at t j = 25/125 c v ce = 400 v u cc = 15 v output inverter e on high t e off high t e on low t e off low t 0,0 0,1 0,2 0,3 0,4 0,5 0,6 0 2 4 6 8 10 12 i c (a) e (mws) t j = t jmax -25c e rec t j = 25c e rec 0,00 0,05 0,10 0,15 0,20 0 2 4 6 8 10 12 i c (a) e (mws) copyright vincotech 8 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 6 output inverter igbt typical switching times as afunction of collector current t = f( i c ) with an inductive load at t j = 125 c v ce = 400 v u cc = 15 v figure 7 output inverter fwd typical reverse recovery time as afunction of collector current t rr = f( i c ) at t j = 25/125 c v ce = 400 v u cc = 15 v output inverter t doff t f t don t r 0,00 0,01 0,10 1,00 10,00 0 2 4 6 8 10 i c (a) t ( m s) t j = t jmax -25c t rr t j = 25c t rr 0,00 0,05 0,10 0,15 0,20 0,25 0,30 0,35 0 2 4 6 8 10 12 i c (a) t rr ( m s) copyright vincotech 9 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 8 output inverter fwd typical reverse recovery charge as afunction of collector current q rr = f( i c ) atat t j = 25/125 c v ce = 400 v u cc = 15 v figure 9 output inverter fwd typical reverse recovery current as afunction of collector current i rrm = f( i c ) at t j = 25/125 c v ce = 400 v u cc = 15 v output inverter t j = t jmax -25c i rrm t j = 25c i rrm 0 1 2 3 4 5 6 0 2 4 6 8 10 12 i c (a) i rrm (a) t j = t jmax -25c q rr t j = 25c q rr 0,0 0,2 0,4 0,6 0,8 1,0 0 2 4 6 8 10 12 i c (a) q rr ( m c) copyright vincotech 10 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 10 output inverter fwd typical rate of fall of forwardand reverse recovery current as a function of collector current d i 0 /d t ,d i rec /d t = f( i c ) at t j = 25/125 c v ce = 400 v u cc = 15 v figure 11 output inverter igbt figure 12 output inverter fwd igbt transient thermal impedance fwd transient thermal impedance as a function of pulse width as a function of pulse width z thjh = f( t p ) z thjh = f( t p ) at at d = t p / t d = t p / t r thjh = 4,72 k/w r thjh = 5,72 k/w igbt thermal model values fwd thermal model values r (k/w) tau (s) r (k/w) tau (s) 0,14 2,1e+00 0,11 3,2e+00 0,66 1,7e01 0,37 2,6e01 2,74 4,0e02 2,69 4,8e02 0,76 6,5e03 0,84 1,2e02 0,42 1,5e03 0,98 2,8e03 0,73 6,0e04 phase change interface output inverter phase change interface t p (s) z thjh (k/w) 10 1 10 0 10 -1 10 -2 10 -4 10 -3 10 -2 10 -1 10 0 10 1 10 10 -5 d = 0,5 0,2 0,1 0,05 0,02 0,01 0,005 0.000 t p (s) z th-jh (k/w) 10 1 10 0 10 -1 10 -2 10 -4 10 -3 10 -2 10 -1 10 0 10 1 10 10 -5 d = 0,5 0,2 0,1 0,05 0,02 0,01 0,005 0.000 0 100 200 300 400 500 600 0 2 4 6 8 10 12 i c (a) di rec / dt (a/ m m m m s) di rec /dt di 0 /dt copyright vincotech 11 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 13 output inverter igbt figure 14 output inverter igbt power dissipation as a collector current as a function of heatsink temperature function of heatsink temperature p tot = f( t h ) i c = f( t h ) at at t j = 175 c t j = 175 c u cc = 15 v figure 15 output inverter fwd figure 16 output inverter fwd power dissipation as a forward current as a function of heatsink temperature function of heatsink temperature p tot = f( t h ) i f = f( t h ) at at t j = 175 c t j = 175 c output inverter 0 5 10 15 20 25 30 35 40 0 50 100 150 200 t h ( o c) p tot (w) 0 2 4 6 8 10 12 14 0 50 100 150 200 t h ( o c) i c (a) 0 5 10 15 20 25 30 35 0 50 100 150 200 t h ( o c) p tot (w) 0 2 4 6 8 10 12 14 0 50 100 150 200 t h ( o c) i f (a) copyright vincotech 12 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 17 output inverter igbt safe operating area as a functionof collector-emitter voltage i c = f( v ce ) at t j t jmax u cc = 15 v output inverter v ce (v) i c (a) 10 3 10 0 10 -1 10 1 10 2 10 1 10 2 10 0 10 3 dc 100ms 10ms 1ms 100s copyright vincotech 13 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 18 output inverter igbt reverse bias safe operating area i c = f( v ce ) at t j = t jmax 25 oc u ccminus =u ccplus switching mode : 3 level switching 0 5 10 15 20 25 0 100 200 300 400 500 600 700 v ce (v) i c (a) v ce max i c module i c chip copyright vincotech 14 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 1 pfc igbt figure 2 pfc igbt typical output characteristics typical output characteristics i d = f( v ds ) i d = f( v ds ) at at t p = 250 s t p = 250 s t j = 25 c t j = 125 c u cc from 7 v to 17 v in steps of 1 v u cc from 7 v to 17 v in steps of 1 v figure 3 pfc fwd typical diode forward current asa function of forward voltage i f = f( v f ) at t p = 250 s pfc 0 20 40 60 80 100 120 0 1 2 3 4 5 6 7 v f (v) i f (a) t j = 25c t j = t jmax -25c 0 20 40 60 80 100 120 0 1 2 3 4 5 6 v ds (v) i d (a) 0 20 40 60 80 100 120 0 1 2 3 4 5 6 v ds (v) i d (a) copyright vincotech 15 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 4 pfc igbt typical switching energy lossesas a function of collector current e = f( i d ) with an inductive load at t j = 25/125 c v ds = 400 v u cc 15 v figure 5 pfc igbt typical reverse recovery energy lossas a function of collector (drain) current e rec = f( i c ) with an inductive load at t j = 25/125 c v ds = 400 v v gs = 15 v pfc t j = t jmax -25c e rec t j = 25c e rec 0,00 0,02 0,04 0,06 0,08 0 5 10 15 20 i c (a) e (mws) e off e on e on e off 0,0 0,1 0,2 0,3 0,4 0,5 0 5 10 15 20 i c (a) e (mws) copyright vincotech 16 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 6 pfc igbt typical switching times as afunction of collector current t = f( i d ) with an inductive load at t j = 125 c v ds = 400 v v gs = 15 v figure 7 pfc fwd typical reverse recovery time as afunction of collector current t rr = f( i c ) at t j = 25/125 c v ce = 400 v v ge = 15 v pfc t doff t f t don t r 0,00 0,01 0,10 1,00 0 5 10 15 20 i d (a) t ( m s) t rr t rr 0,00 0,01 0,02 0,03 0,04 0,05 0 5 10 15 20 i c (a) t rr ( m s) copyright vincotech 17 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 8 pfc fwd typical reverse recovery charge as afunction of collector current q rr = f( i c ) atat t j = 25/125 c v ce = 400 v v ge = 15 v figure 9 pfc fwd typical reverse recovery current as afunction of collector current i rrm = f( i c ) at t j = 25/125 c v ce = 400 v v ge = 15 v pfc t j = t jmax - 25c i rrm t j = 25c i rrm 0 5 10 15 20 0 5 10 15 20 i c (a) irr m (a) t j = t jmax - 25c q rr t j = 25c q rr 0,0 0,1 0,2 0,3 0,4 0,5 0,6 0 5 10 15 20 i c (a) q rr ( m c) copyright vincotech 18 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 10 pfc fwd typical rate of fall of forwardand reverse recovery current as a function of collector current d i 0 /d t ,d i rec /d t = f( i c ) at t j = 25/125 c v ce = 400 v v ge = 15 v figure 11 pfc igbt figure 12 pfc fwd igbt transient thermal impedance fwd transient thermal impedance as a function of pulse width as a function of pulse width z thjh = f( t p ) z thjh = f( t p ) at at d = t p / t d = t p / t r thjh = 2,56 k/w r thjh = 3,87 k/w r (k/w) tau (s) r (k/w) tau (s) 0,21 0,780 0,11 2,763 1,120 0,117 0,56 0,226 0,829 0,044 2,29 0,051 0,314 0,005 0,62 0,008 0,078 0,001 0,28 0,002 phase change interface igbt thermal model values pfc phase change interface fwd thermal model values t p (s) z thjh (k/w) 10 1 10 0 10 -1 10 -2 10 -4 10 -3 10 -2 10 -1 10 0 10 1 10 10 -5 d = 0,5 0,2 0,1 0,05 0,02 0,01 0,005 0.000 t p (s) z thjh (k/w) 10 1 10 0 10 -1 10 -2 10 -4 10 -3 10 -2 10 -1 10 0 10 1 10 10 -5 d = 0,5 0,2 0,1 0,05 0,02 0,01 0,005 0.000 0 1000 2000 3000 4000 5000 6000 7000 0 5 10 15 20 i c (a) di rec / dt (a/ m s) di 0 /dt di rec /dt copyright vincotech 19 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 13 pfc igbt figure 14 pfc igbt power dissipation as a collector/drain current as a function of heatsink temperature function of heatsink temperature p tot = f( t h ) i c = f( t h ) at at t j = 175 oc t j = 175 oc u cc = 10 v figure 15 pfc fwd figure 16 pfc fwd power dissipation as a forward current as a function of heatsink temperature function of heatsink temperature p tot = f( t h ) i f = f( t h ) at at t j = 175 oc t j = 175 oc pfc 0 15 30 45 60 75 0 50 100 150 200 t h ( o c) p tot (w) 0 5 10 15 20 25 0 50 100 150 200 t h ( o c) i c (a) 0 10 20 30 40 50 0 50 100 150 200 t h ( o c) p tot (w) 0 5 10 15 20 0 50 100 150 200 t h ( o c) i f (a) copyright vincotech 20 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 17 pfc igbt safe operating area as a functionof drain-source voltage i d = f( v ds ) at d = single pulse t h = 80 oc u cc = 15 v t j = t jmax oc figure 18 pfc igbt reverse bias safe operating area i c = f( v ce ) at t j = t jmax 25 oc pfc v ds (v) i d (a) 10 0 10 -1 10 1 10 2 10 3 10us 100us 1ms 10ms 100ms dc 10 2 10 1 0 10 20 30 40 50 60 70 0 100 200 300 400 500 600 700 v ce (v) i c (a) v ce max i c module i c chip copyright vincotech 21 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 1 rectifier diode figure 2 rectifier diode typical diode forward current as diode transient thermal impedance a function of forward voltage as a function of pulse width i f = f( v f ) z thjh = f( t p ) at at t p = 250 s d = t p / t r thjh = 3,66 k/w figure 3 rectifier diode figure 4 rectifier diode power dissipation as a forward current as a function of heatsink temperature function of heatsink temperature p tot = f( t h ) i f = f( t h ) at at t j = 150 oc t j = 150 oc input rectifier bridge 0 5 10 15 20 25 0,0 0,5 1,0 1,5 2,0 v f (v) i f (a) t j = 25c t j = t jmax -25c t p (s) z thjc (k/w) 10 1 10 0 10 -1 10 -2 10 -4 10 -3 10 -2 10 -1 10 0 10 1 10 10 -5 d = 0,5 0,2 0,1 0,05 0,02 0,01 0,005 0.000 0 10 20 30 40 50 0 30 60 90 120 150 t h ( o c) p tot (w) 0 5 10 15 20 25 30 0 30 60 90 120 150 t h ( o c) i f (a) copyright vincotech 22 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 1 pfc shunt figure 2 dc shunt pulse power r1 pulse power r2 d r / r 0 < 1% after 1 pulse d r / r 0 < 1% after 1 pulse d r / r 0 < 1% after 10.000 cycles; duty cycle< 0,1% d r / r 0 < 1% after 10.000 cycles; duty cycle< 0,1% figure 1 thermistor typical ntc characteristicas a function of temperature r t = f( t ) shunt thermistor ntc-typical temperature characteristic 0 4000 8000 12000 16000 20000 24000 25 45 65 85 105 125 t (c) r/ t pulse (ms) p low (w) 10 1 singlerepetitive 10 3 10 2 10 0 10 1 10 0 10 1 10 2 10 3 10 4 t pulse (ms) p low (w) 10 1 singlerepetitive 10 1 10 2 10 0 10 0 10 2 10 3 10 4 10 3 10 1 copyright vincotech 23 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet t j 125 c figure 1 output inverter igbt figure 2 output inverter igbt turn-off switching waveforms & definition of t doff , t eoff turn-on switching waveforms & definition of tdon, t eon (t eoff = integrating time for e off ) (t eon = integrating time for e on ) 201b06ipb010rcp955a40 u in (0%) = 0 v u in (0%) = 0 v u in (100%) = 5 v u in (100%) = 5 v v c (100%) = 400 v v c (100%) = 400 v i c (100%) = 6 a i c (100%) = 6 a t doff = 0,95 s t don = 0,63 s t eoff = 1,12 s t eon = 0,84 s figure 3 output inverter igbt figure 4 output inverter igbt turn-off switching waveforms & definition of t f turn-on switching waveforms & definition of t r v c (100%) = 400 v v c (100%) = 400 v i c (100%) = 6 a i c (100%) = 6 a t f = 0,02 s t r = 0,03 s switching definitions output inverter general conditions = i c 1% v ce 90% v ge 90% -25 0 25 50 75 100 125 -0,2 0 0,2 0,4 0,6 0,8 1 1,2 time (us) % t doff t eoff v ce i c v ge i c10% v ge10% t don v ce 3% -50 0 50 100 150 200 2,9 3,1 3,3 3,5 3,7 3,9 time(us) % i c v ce t eon v ge fitted i c10% i c 90% i c 60% i c 40% -25 0 25 50 75 100 125 0,6 0,7 0,8 0,9 1 1,1 1,2 time (us) % v ce i c t f i c10% i c90% -25 0 25 50 75 100 125 150 175 200 3,5 3,6 3,7 3,8 3,9 4 time(us) % t r v ce i c copyright vincotech 24 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 5 output inverter igbt figure 6 output inverter igbt turn-off switching waveforms & definition of t eoff turn-on switching waveforms & definition of t eon p off (100%) = 2,39 kw p on (100%) = 2,39 kw e off (100%) = 0,20 mj e on (100%) = 0,32 mj t eoff = 1,12 s t eon = 0,84 s figure 7 output inverter fwd turn-off switching waveforms & definition of t rr v d (100%) = 400 v i d (100%) = 6 a i rrm (100%) = 6 a t rr = 0,28 s switching definitions output inverter i c 1% v ge 90% -25 0 25 50 75 100 125 -0,2 0 0,2 0,4 0,6 0,8 1 1,2 time (us) % p off e off t eoff v ce 3% v ge 10% -50 0 50 100 150 200 2,9 3,1 3,3 3,5 3,7 3,9 time(us) % p on e on t eon i rrm 10% i rrm 90% i rrm 100% t rr -120 -80 -40 0 40 80 120 3,5 3,6 3,7 3,8 3,9 4 time(us) % i d v d fitted copyright vincotech 25 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet figure 8 output inverter fwd figure 9 output inverter fwd turn-on switching waveforms & definition of t qrr turn-on switching waveforms & definition of t erec (t qrr = integrating time for q rr ) (t erec = integrating time for e rec ) i d (100%) = 6 a p rec (100%) = 2,39 kw q rr (100%) = 0,67 c e rec (100%) = 0,16 mj t qrr = 0,55 s t erec = 0,55 s switching definitions output inverter t qrr -150 -100 -50 0 50 100 150 3,5 3,6 3,7 3,8 3,9 4 4,1 4,2 4,3 % i d q rr time(us) -25 0 25 50 75 100 125 3,6 3,8 4 4,2 4,4 time(us) % p rec e rec t erec copyright vincotech 26 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet ordering code in datamatrix as in packaging barcode as 201b06ipb010rcp955a40 p955a40 p955a40 201b06ipb010rcp955a40/3/ p955a40 p955a40/3/ 20pb06ipb010rcp955a40y p955a40y p955a40y 20pb06ipb010rcp955a40y/3/ p955a40y p955a40y/3/ x y 45 0 42 0 39 0 36 0 33 0 30 0 27 0 24 0 21 0 18 0 15 0 12 0 9 0 6 0 3 0 0 0 0,2 26,4 4,8 26,4 9,8 26,4 14,8 26,4 19,8 26,4 22,5 26,4 25,2 26,4 30,2 26,4 35,2 26,4 40,2 26,4 45,2 26,4 outline pinout ordering code & marking ordering code and marking - outline - pinout version without thermal paste, solder pins 9 10 pin table pin 12 3 4 5 6 7 8 27 with thermal paste, solder pins 2324 25 26 1920 1112 without thermal paste, press fit pinswith thermal paste, press fit solder pins 2122 1718 1314 15 16 copyright vincotech 27 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet vcc vbs rcin itrip enable fault lo1,2,3 ho1,2,3 v it,th+ 3.3v 0 0 0 15v 15v > v rcin,th 0 3.3v high imp /lin1,2,3 /hin1,2,3 15v 15v > v rcin,th 0 0 high imp 0 0 201b06ipb010rcp955a40 20pb06ipb010rcp955a40y static logic funtion table application data copyright vincotech 28 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet pin # 12 3 4 5 6 7 8 9 1011 12 13 1415 16 17 18 19 20 21 22 23 24 25 26 27 pin descriptions pin name ntc2ntc1 invs + invs en ?fault ?lin3?lin2 u v w dc2 + dc2 pfc dc1 pfc + (coil) dc1 + (coil) ac2 ac1 freq vsense ?lin1 output for u phase inverter input dc + inverter input dc pfc return rectifier output dc pfc coil connector rectifier output dc + gnd2 v cc rectifier input pfc switching frequency adjust pfc bulk voltage sense ?hin3?hin1 ?hin2 temperature sensor connector 1 pin description output for w phase fault output, indicates over current or under voltage (negative logic, opendrain output) enable i/o functionality inverter sense resistor lowside inverter sense resistor highsidesignal input for highside w phase signal input for lowside u phase signal input for lowside v phaseoutput for v phase temperature sensor connector 2signal input for lowside w phase inverter ground driver circuit supply voltage signal input for highside u phase signal input for highside v phaserectifier input copyright vincotech 29 28 jul. 2015 / revision 3
20-PB06IPB010RC-P955A40Y 20-1b06ipb010rc-p955a40 datasheet disclaimerlife support policy as used herein: vincotech products are not authorised for use as critical components in life support devices or systems without the express written approval of vincotech. 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in labelling can be reasonably expected to result in significant injury to the user. 2. a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. the information, specifications, procedures, methods and recommendations herein (together information) are presented by vincotech to reader in good faith, are believed to be accurate and reliable, but may well be incomplete and/or not applicable to all conditions or situations that may exist or occur. vincotech reserves the right to make any changes without further notice to any products to improve reliability, function or design. no representation, guarantee or warranty is made to reader as to the accuracy, reliability or completeness of said information or that the application or use of any of the same will avoid hazards, accidents, losses, damages or injury of any kind to persons or property or that the same will not infringe third parties rights or give desired results. it is readers sole responsibility to test and determine the suitability of the information and the product for readers intended use. copyright vincotech 30 28 jul. 2015 / revision 3

▲Up To Search▲

Price & Availability of 20-PB06IPB010RC-P955A40Y

	To Download 20-PB06IPB010RC-P955A40Y Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .